Main Discussion Area > HowTo's and Build-a-longs
Juniper limb build along
Keenan:
The Journey started in a subdivision where they were clearing some juniper trees. The limb in the middle is the branch usedfor this bow.
Much like surgery a screening process is done to see if the pateint (branch) will survive the process. Though there were alot of very small twigs on the limb their were no major knots that would be a problem except one that was off the bottom and would be cut out with the waist since I was only using the top.
The second pic shows a vertical line (top of limb) and a horizontal (first cut with band saw)
Third pic shows the heart wood. The next two cuts will follow along the edge of the heart wood.
Fourth pic juniper on the right trimmed down and left to dry for 11 months.
Five and six are rough dow to floor tiller.
[attachment deleted by admin]
Keenan:
Many processes are similar to surgery. I will try to explain along the way.
Now after 11 months of drying in the corner,(Scheduling and consulting with the physcian) (Bowyer looking at stave trying to figure out where the bow is in the stave) The patient is prepaired for skin grafts (sinew) to strengthen the back. First pic. Ofcoarse the skins grafts (sinew) came from a donor (elk) The tends dried, pounded and shredded ready for the procedure.
With the patient scrubed (toothed the surface with hack saw) and operating table ready we begin the first one hour surgery.
Third pic shows the patient with airway established and all the monitors hoocked up (just for fun) Since I didn't really have to keep this patient alive and breathing I do think I can charge as much for building bows,lol
Four- Vital fluids (sinew) kept on warmer ready for soaking the grafts.
Five and six- grafts aplied / patient put in traction to recover,
[attachment deleted by admin]
Ryano:
:o ::) :o ::) :o Your scaring me in that Doctors outfit there Keenan! lol...... The bow looks good though.... ;D
Keenan:
Ok here we are about two weeks later, Sinew dried into a nice reflex we are ready for the horm handle overlay. For this I have taken a Gemsbok horn and have split and found a section about the right width and contour.
After some sanding on both the inside of the horn and the back of the bow, we have a nice fit and are ready to glue. Here again the bowyer's task are much like the physcain's with the bone graft and all.
By slightly wetting the horn and placing on the bow I can see detect any high or low spots to make a better fit.
Since I will be waiting for glue to set I will prepare the tips at the same to. (Dual surgery)("while we are in there we will strengthen any week spots") (tips).
The tips are sanded on the belt sander at a slight angle just enough to create a flat surface for our tip build-up.
The zebra wood has been cut so that the grain stripes are parallel to the base. And are let squared to aid in clamping.
[attachment deleted by admin]
Keenan:
Ryano, my wife is an ultrasound teck at the hostpital so scrub outfits are common wardrobe around our house.
lAll surfaces are dampened then glued with gorrilla glue. Because the horn wraps over the edge slightly Multiple clamps are required.
Next once dried they are roughed out with a half round basterd file. Since the ridges were fairly close together I removed every other ridge.
Often bowyers use saws to cut out work and once again surgens as well use saws. (Scary Part) Sure glad they are much more precise with their cuts.
Now with tips and horn shaped out and about 22 days of drying on the sinew we are ready for more skin grafts.
The back of the bow is coated again with sinew glue while the skin is soaked in warm sinew glue untill soft and pliable. I always pre-fit around the tips and work from the tips toward the handle area.
[attachment deleted by admin]
Navigation
[0] Message Index
[#] Next page
Go to full version