« previous next »
Pages: [1]

Author Topic: First Bendy Handle Dimensions?  (Read 2840 times)

0 Members and 1 Guest are viewing this topic.

Offline Cade

  • Member
  • Posts: 64
First Bendy Handle Dimensions?
« on: February 10, 2015, 07:16:43 pm »
I have a real clean hickory stave that is a little too thin to make stiff handled and I would like to try a bend in the handle for the first time. It is 68" ttt. My question is what dimensions should I do?
« Last Edit: February 11, 2015, 09:05:03 am by cman3 »
Logged

Offline dylanholderman

  • Member
  • Posts: 787
Re: First Bendy Handle Dementions?
« Reply #1 on: February 10, 2015, 07:55:43 pm »
i dont know how much this will help but the finished dimensions my bendy handle maple bow at the handle are 1 1/2in wide and 3/4in thick if that helps. :)
personally i would start out a bit thicker in the handle like say a one inch and work it down from there ;) 
Logged

Offline RyanY

  • Member
  • Posts: 1,997
Re: First Bendy Handle Dementions?
« Reply #2 on: February 10, 2015, 08:00:10 pm »
What's your desired draw weight and draw length?  ???
Logged

Offline Hrothgar

  • Member
  • Posts: 1,475
Re: First Bendy Handle Dementions?
« Reply #3 on: February 10, 2015, 09:26:26 pm »
If you have a good 68" to work with, another option might be to trim off a couple inches without changing the thickness or width in the handle area.  This might stiffen up the handle some...if that's what you're wanting.
« Last Edit: February 10, 2015, 09:42:05 pm by Hrothgar »
Logged
" To be, or not to be"...decisions, decisions, decisions.

Offline Cade

  • Member
  • Posts: 64
Re: First Bendy Handle Dementions?
« Reply #4 on: February 10, 2015, 10:50:57 pm »
I'm going for 26 at around 45lbs. Should I cut it shorter? And how wide is too wide at the handle?
Logged

Offline RyanY

  • Member
  • Posts: 1,997
Re: First Bendy Handle Dementions?
« Reply #5 on: February 10, 2015, 11:05:14 pm »
With your stats you have a lot of room to work with. I just finished a bow that was 58" ntn and 45#@27" that was 1.25" at the handle and 1.5" wide at the fades. If you're just looking for some dimensions I think 64" ntn and 1.25" wide for the middle 1/3 of the bow would be a good start.
Logged

Offline Cade

  • Member
  • Posts: 64
Re: First Bendy Handle Dementions?
« Reply #6 on: February 10, 2015, 11:27:35 pm »
Thanks Ryoon. I think I'll cut it out to those dimensions this weekend.
Logged

Offline George Tsoukalas

  • Member
  • Posts: 9,425
    • Traditional and Primitive Archers
Re: First Bendy Handle Dementions?
« Reply #7 on: February 11, 2015, 08:56:00 am »
What is your draw length? Jawge
Logged
Set Happens!
If you ain't breakin' you ain't makin!

Offline Cade

  • Member
  • Posts: 64
Re: First Bendy Handle Dementions?
« Reply #8 on: February 11, 2015, 09:02:44 am »
I was wanting 26 at around 45
« Last Edit: February 11, 2015, 11:25:17 am by cman3 »
Logged
Pages: [1]
« previous next »