Author Topic: Fire pit stave???  (Read 7501 times)

0 Members and 2 Guests are viewing this topic.

Offline Pat B

  • Administrator
  • Member
  • Posts: 38,104
Re: Fire pit stave???
« Reply #45 on: March 10, 2026, 12:24:08 am »
Can't say I have either. Could be a resin pocket or something similar. You never really know what is under a ring until you remove it and that would be ashamed to do with this bow considering the work you put into it. Can you tell if the bubble is hollow?
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Selfbowman

  • Member
  • Posts: 3,539
Re: Fire pit stave???
« Reply #46 on: March 10, 2026, 12:33:15 am »
No I can’t push it down but I know it’s hollow.. drill a hole and fill it with glue??? It’s not affecting it right now. It’s about 3/8x1/2” oval.
Well I'll say!!  Osage is king!!

Offline bentstick54

  • Member
  • Posts: 1,019
Re: Fire pit stave???
« Reply #47 on: March 10, 2026, 01:17:20 pm »
I’ve never seen it. What part of the limb is it on.?

Offline Pat B

  • Administrator
  • Member
  • Posts: 38,104
Re: Fire pit stave???
« Reply #48 on: March 10, 2026, 01:43:07 pm »
I'd say at least drill a hole and put glue in it. might clamp it until the glue sets. I'd be curious to know what it is so if there is a failure an autopsy may be the thing.
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Online Burnsie

  • Member
  • Posts: 97
Re: Fire pit stave???
« Reply #49 on: March 10, 2026, 05:15:17 pm »
Circling back to the grain run-off discussion earlier in the thread - I got to thinking. Every bow is made to taper towards the tips, some to pretty thin delicate tips.
So, grain run-off always happens for a good portion of the limbs length depending on where you start your taper.   No way to avoid it.
I guess we are only concerned with severe run-off where the grain takes a sharp turn off the edge of the bow?

Offline bentstick54

  • Member
  • Posts: 1,019
Re: Fire pit stave???
« Reply #50 on: March 10, 2026, 07:34:59 pm »
Burnsie, that has been my experience.

Offline Selfbowman

  • Member
  • Posts: 3,539
Re: Fire pit stave???
« Reply #51 on: March 10, 2026, 10:01:49 pm »
Mid limb. Ya I was thinking the same about run off in tip tapers.
Well I'll say!!  Osage is king!!

Offline bentstick54

  • Member
  • Posts: 1,019
Re: Fire pit stave???
« Reply #52 on: Today at 11:36:09 am »
Arvin, what ever happened with the bubble that appeared? Did you drill to see if it was hollow and fill it with glue, or leave it alone? Curios minds want to know.

Offline Selfbowman

  • Member
  • Posts: 3,539
Re: Fire pit stave???
« Reply #53 on: Today at 11:48:21 am »
Noting it shrank some and  I’m going to treat it as a knot. You need a recurve shooter to shoot we it I don’t care for recurve bows especially short ones.  Think no larger than that bubble is no need to worry about it,
Well I'll say!!  Osage is king!!

Offline bentstick54

  • Member
  • Posts: 1,019
Re: Fire pit stave???
« Reply #54 on: Today at 01:45:24 pm »
What final draw weight and draw length did you settle at?

Online Jim Davis

  • Member
  • Posts: 1,410
  • Reparrows
    • Reparrows
Re: Fire pit stave???
« Reply #55 on: Today at 02:27:10 pm »
Back to the run off issue,  the grain of a pyramid bow runs off the full length of the limbs... .
Jim Davis

Kentucky--formerly Maine

Online sleek

  • Administrator
  • Member
  • Posts: 7,336
Re: Fire pit stave???
« Reply #56 on: Today at 04:22:20 pm »
Back to the run off issue,  the grain of a pyramid bow runs off the full length of the limbs... .

Yup, and I use that knowledge all the time when making bows with character. As long as the grain run off is gradual, and tapered, you can get away with some things you wouldn't expect.
Tread softly and carry a bent stick.

Dont seek your happiness through the approval of others