Primitive Archer
Main Discussion Area => Bows => Topic started by: Bow Nut on June 24, 2011, 06:26:16 pm
-
This is the elm log I got yesterday and I am trying to split it today. I started a wedge in straight down and the split ws looking good unitll it got about midway into the heart wood than it turned a 90 degree angle. Is this a bad indication for this wood and is this going to be ok should I keep splitting it and knock that 1/4 off?
-
Your startin the split on the end first right, and not down the log to begin with? Chanced are if your log is big enough you can cut a good foot off and be fine, but your probably gonna quarter it eventually anyway, so I think all in all it would be fine. IMO
-
I think splitting is always a bit hit or miss, some woods are more difficult than others due to interlocking grain. I think Elm is one of those if I remember right... long time since I split Elm.
I'd say carry on now you've started, but once it's in half, get that sucker on the bandsaw.
Del
-
yea started on the end and you can see how deep it went ant then I started walking the wedges down the log and that happended. maybe I should have gone deeper yea I hope to get 8 staves out of it.
-
yea it is about 12 to 13 inches in diameter might have to quater it so it is more managable on the band saw anyway.
-
I've had that happen too. The last log I split did that. I started splitting from the middle and had more success. I may be inclined to start that split right in that drying crack. Jawge
-
I split till my hands hurt today .I always start at the end and then leapfrog my wedges as the split develops seems to work for me.It also seems to follow the natural grain of the wood easier.
-
I find at least 2 sharp axes, a nylon/copper hammer and some old broken bow tips as wedges works wonders with elm. If the split starts to wonder correct it a little with the next axe hammered in. I have had much more luck starting the split from the middle of the log as above.
(http://i121.photobucket.com/albums/o218/dwardo/IMAG1133.jpg)
-
well I tried going in from the center of the end and got a nice even crack across as I started walking my wedges down it started doing the same thing again but worse. I gave up on it and broke out the chain saw and just cut the sucker right down the middle. I spent 1 hour with sledge and wedges and made it now wear and spent 20 minutes with the chainsaw and poof it was in half lol not traditional I know but I had already ruined at least one staves worth of wood on it and did not want to ruin any more. Might get a billet or two out of that section though. Thanks for all the advise but this dang log was tuff as nails and I just could not risk ruining more of it. Maybe with a bit more practice I can split elm. the osage I have been using was from a log I bought from a local wood supplier. Imagine that a hard wood lumber supplier with a osage log in Ga. I split it after it was already dry as he had it there for 2 years and It split great only took me an hour to get my staves out off it. I guess the interlocking grain makes a big difference. now I know for next time as I have already spotted more elm that I can harvest.
-
I've split elm for firewood and cussed so hard I took the finish off the axe handle...cannot imagine splitting a big log like that. Kudos to you for sticking with it!
-
Hi Folks, The issue of splitting elm has come up before. There are a few folks that get good at it, but elm is the very devil to split cleanly. My one experience convinced me that just about any other wood is easier to work with. A common suggestion is to run a kerf down at least one side to control the split. Having a series of hatchets to cut connecting fibers is very helpful. One suggestion I read recently ( wish I could remember who) was to just get out a big drill and start placing a line of lag screws down the log. He said the log would eventually just pop open along the line of screws. Ron
-
Splitting elm sucks....BAD. I split one elm log and don't plan on doing it again any time soon. I would rather split 10 osage logs than one elm.
-
ELM is a BEAST is'nt it but that inter locking grain sure makes a nice bow.
-
When I was a kid I went to confession and for my pennance the priest told me I needed to split an old log into firwood he had laying behind the monastery, either that or say 10 rosaries. I chose the log, looking back I am pretty sure it was elm, it seemed like I pounded on that thing everyday after school for weeks to get it split. I triesd another log later in life and ended up putting a deep kerf on each side with my skill saw.
-
I second the kerf cutting idea. Here's a link to my experience with elm, if you're interested.
http://www.primitivearcher.com/smf/index.php/topic,25759.msg346004.html#msg346004 (http://www.primitivearcher.com/smf/index.php/topic,25759.msg346004.html#msg346004)
-
If you started your wedge at the wider crack that I didn't point an arrow to, then all that has happened is the wood is trying to split to the path of least resistance which is the lateral grain. Keep in mind that the geographic center of the wood is not necessarily going to be the center of growth. A picture being worth a thousand words should explain it better than I can with a bunch of words.
-
Critical of my own spelling. ;D
-
yea that is where I started and I started there again the second go at it and the sucker split all the way accross in a straight line then when I started walking my wedges it just ween off around the core again following a ring. like in the picture
-
Here is the way I do
start a thin wedge at crack in growth center ,then a wedge from the side of log that will knock the first wedge out as it goes in, then keep driving wedges in from that side to move down along the log , start each new wedge at the point farthest from the last one that you can still see through the log no further a way or you will be starting a new split !
Read this twice then ask Questions
"keep it simple keep it fun"
Guy