Primitive Archer
Main Discussion Area => Bows => Topic started by: ajooter on April 17, 2016, 08:39:01 pm
-
(http://i.imgur.com/Oy8HnWK.jpg?1)(http://i.imgur.com/e2Eypsb.jpg?1)(http://i.imgur.com/LKMW0T6.jpg?1)
Got a nice sassafras board from a generous fellow. He makes gorgeous custom turkey calls. We had a lot to talk about and he hooked me up with a nice chunk of Osage and a great big sassafras board. I wanted to make him a bow since he shoots traditional. This first one will be a stiff handled bow. I was going for a 45# bow. The stave is 72" long so I have a lot of room to work with. I was gonna start 2.5" wide and hold that width for a heavy 2/3 of the limb and taper down to the nocks. If I need to drop draw weight I have room to width tiller the bow a little. This piece seems nice and dense and it hasn't been hard to chase a ring.
Any comments and suggestions are welcome!
-
I have another piece I want to try making an elbow with. I hear this wood likes that design.
On another note...this is the best smelling wood to work! When I used to live in PA we used to use sassafras to smoke our burgers and dogs!! Adds some great flavor to meats!
-
Makes a tasty burger for sure! I've also made one bow from a board, been about 6-7 years ago though. Don't really remember the stats. I'd love to see this one finished. I have a stave that's been drying since last fall. I have a few nice size sass trees on the new property. Good luck with it.
Tattoo Dave
-
Sassafras bows are the lightest weighting bows I've ever made.
One thing make sure your woods season. Because sassafras soaks up relative humidity more than hickory. You know if it is when you get down to your ready for finish. Limbs look nice next morning your limbs might be warped.
I had this happen twice, I had to but them in the hot box to get ride of moisture. Re tiller put in the hot box as low as it'll go then crack the lead.
By far my not my favorite bow wood.
-
ajooter, ;D you're kinda getting addicted to this aren't you?
-
I don't know own what your talking about Fred! O:)
-
(http://i.imgur.com/02yMxEK.jpg?1)
went down couple more rings to get a flat back across the while stave.
-
I am over a year into one. I will be watching.
-
Mine was fun ... and it REEEALLY likes dry heat. Would do another if the right piece shows up.
-
(http://i.imgur.com/UFkPpGB.jpg?1)(http://i.imgur.com/aM1dH2h.jpg?1)
I got one of the limbs roughed down. Due to the layout I only ended up with 2" wide limbs. The limb thickness runs about 5/8" right now. The wood works like red oak....very ring porous!
Depending on how she tillers out I may try some dry heat Knoll.
-
Keep it as long as you can and keep all the width you can. Also, it takes a lot of wood to make a bow, so watch that thickness closely. It will go fast.
-
Your telling me pearly...she's got a good deal of flex even at better then 5/8" thick!
-
(http://i.imgur.com/0FaJOHg.jpg?1)(http://i.imgur.com/fLf7RPf.jpg?1)(http://i.imgur.com/VcCk47d.jpg?1)(http://i.imgur.com/1YcvUu9.jpg?1)(http://i.imgur.com/Bw7Y4jR.jpg?1)
I got the other limb roughed down to 2" wide and then narrowed the tip down a little. I then further tapered to belly till I had a decent floor tiller. I noticed a spot in the limb that may need some work due to the pronounced growth rings in this stuff. I love the way the growth rings feather out of the handle. I will be putting some kind of tip overlays on her before I start tillering...haven't decided just yet what I want to use. I may also let the bow sit in the garage and monitor the weight...it seems drier then a popcorn fart to me but I'll check the weight over a week in the garage and see what happens.
-
I rounded the limb edges on the belly a little as well. I know knoll said this wood likes dry heat...what kind of heat should I use the gently flip the tips...Steam or dry?
-
(http://i.imgur.com/8ZUV07o.jpg?1)(http://i.imgur.com/Hm0LdgG.jpg?1)(http://i.imgur.com/6pRWRta.jpg?1)(http://i.imgur.com/NZFGTBp.jpg?1)
finished the rough out of the second limb and cleaned up the handle a little. I really like the grain in this wood even if it is crazy porous!! all those broke red oak bows paid off when working this wood. she's got a little twist and some potential alignment issues but starting to look like a bow.
unfortunately I'm told no more bow work till I clean up the garage...if you haven't noticed my background I'll be busy for the rest of the day probably into tomorrow haha.
-
(http://i.imgur.com/MwAfNhM.jpg?1)
(http://i.imgur.com/3tgZH5U.jpg?1)
Used some osage for tip overlays. The tips are pretty chunky right now but I'll narrow then down as I start to tiller. I need to steam the handle and try to get the tips to line up.
-
(http://i.imgur.com/e5tEU41.jpg?1)
I got the handle steamed and hopefully lined up...thank you Gordon for your infinite wisdom. I'll let it sit overnight and see how it comes out!
-
Looking mighty sassy!
-
chimed in the master of puns ;)
-
Shut up and get back to work on that bow, I wanna see how it turns out!
-
That sassy bow needs to sit overnight. I was going to use some dry heat to reflex and heat treat both limbs. Do you think I should do it first thing....or wait till I have it tillered to brace?
-
I kinda like to do it before I get too deep into tillering.