Primitive Archer
Main Discussion Area => Bows => Topic started by: JW_Halverson on May 27, 2016, 08:11:23 pm
-
I hope someone has plans for one of these string jigs that they could share with me (and others). Anyone?
-
Calculate finished string length, drill four holes in a rectangular shape in a board with the correct circumference to equal string length. Install bolts and make string. Serve loops together with string stretched to proper length between two bolts.
-
Calculate finished string length, drill four holes in a rectangular shape in a board with the correct circumference to equal string length. Install bolts and make string. Serve loops together with string stretched to proper length between two bolts.
I had to do that for one bow string....now I want to continue with other bow lengths, hence the jig thingy. LOL
-
Drill a new set of holes and move the bolts. You only need to move one end. ;)
-
My first string jig was 2, 16d nails, one at one end of my work bench and at the other end a series of holes at 1" intervals. The nails slipped in and out of the holes as needed.
-
I use one like this. It's been accurate for me.
http://www.primitivearcher.com/smf/index.php?topic=41114.0
-
A Google search turned up a bunch of them.
-
I have two lengths of Dexion (angle iron with holes all along it that is used for bolting together to make racking/shelving) A short bit is welded sticking up at each end and a fence eye bent into a hook used to hold the ends of the string.
Here's a pic of the mk1 here:-
http://bowyersdiary.blogspot.co.uk/2011/05/roys-bow-and-stringing-jig.html (http://bowyersdiary.blogspot.co.uk/2011/05/roys-bow-and-stringing-jig.html)
Del
-
How do you stretch the string between two bolts? Maybe with some kind of screw (like in a clamp) to separate the bolts.. eh
Is there a less annoying, but simple 'setup' that allows serving the loops? 4 bolts and then moving to 2 bolts for finishing the serving sounds good ...
-
How do you stretch the string between two bolts? Maybe with some kind of screw (like in a clamp) to separate the bolts.. eh
Is there a less annoying, but simple 'setup' that allows serving the loops? 4 bolts and then moving to 2 bolts for finishing the serving sounds good ...
Bottom pic shows how the two lengths of Dexion are bolted to provide coarse length adjustment. The nuts on the hooks provide fine adjustment and tensioning. Don't look too closely at the "welding" (or glueing with slag) :-[
To pull one side of the string out of the way while I serve, I use an S shaped bit of wire to hook it down into one of the holes in the dexion.
I've just added a picture showing the hook pulling down a bit of random string! That allows you to serve the upper bit.
Del
-
I use one like this. It's been accurate for me.
http://www.primitivearcher.com/smf/index.php?topic=41114.0
I absolutely love that jig...for making Flemish twisted strings. Been using the same 2x4 with finish nails for 14 years! The top of the jig where you cut the strands is grooved mighty deep from all the cuts. Only reason I have not tossed it and upgraded to a nicer version is that I wanna see if the groove goes all the way thru the 2x4 eventually!
-
I made this one myself, you can get uni-strut at Lowe's
1-5/8" x 3/4" I think they are 12' long
I cut the main rail 6' long and the two shorter ones 16"
(http://i1293.photobucket.com/albums/b593/osagemark/site%20window/100_0836.jpg) (http://s1293.photobucket.com/user/osagemark/media/site%20window/100_0836.jpg.html)
You need two washers out of 1/4" thick steel and two 3/8 allen head bolts, two more bolts for the pins (Poles) below (you can't get a wrench under there)!
My Poles (pins) are 1" round 2-1/2 tall, drill and tap 3/8" on the bottom and drill and ream for 3/8" cold roll pin or long dowel pins, total height is 4-1/2" tall. you need the room for serving.
From pin to pin needs to be center to the bolt in the middle.
Start out with all 3 uni-strut in a line, now all 4 pins are in a line, measure from outside pin to outside pin is your string length. You may have to file one of the slots in the uni-strut to get the length.
Wrap you starting point on the inside pin I use cloths pins to hold the string.
wrap around how ever many strands you want and back to the starting place with the cloths pin.
Now you want to turn the other end without the cloths pin to 90 degrees, use a speed square to get it square.
Wrap your serving , now turn the same end back in line (all 4 pins lined up) wrap serving to finish your loop.
now you can do the other end with the cloths pin
(http://i1293.photobucket.com/albums/b593/osagemark/site%20window/100_0837.jpg) (http://s1293.photobucket.com/user/osagemark/media/site%20window/100_0837.jpg.html)
-
Looks like that design will allow a person to make loops of different sizes as well (for example, I want 6 inch loops for a horsebow right now), Mad Max.
That helps a lot.
Del's has some features I am mulling over as well. I will probably cobble together some Frankenstein version and get by with it for a while.
-
Looks like that design will allow a person to make loops of different sizes as well (for example, I want 6 inch loops for a horsebow right now), Mad Max.
That helps a lot.
Del's has some features I am mulling over as well. I will probably cobble together some Frankenstein version and get by with it for a while.
Yea I have made 5-1/2" loops
You might want to cut those 16" to 18" or more
Good luck
-
Made this one many years go. Fairly easy to make and still use it
-
Nice thanks, I need to make one of those one day.. I guess the rotating stuff would work similarly to having 4 nails and then 2 nails spaced further apart, always with the same circumference?
There's also this one arm jig https://www.youtube.com/watch?v=L69T4Hy4iv8
-
Here is my version John
-
Mine is like the last couple shown but made out of wood with a sliding joint so I can store it in two pieces. I've been meaning to make a Mk11 version for a while now.
-
Just well add mine. ;) Don't use it much anymore but worked great when I did. I have it marked for what length you want and you just adjust on end to that mark. :)
Pappy