Author Topic: Reducing the spine of a cane  (Read 3885 times)

0 Members and 1 Guest are viewing this topic.

Offline RidgeRunner

  • Member
  • Posts: 1,153
Reducing the spine of a cane
« on: October 06, 2008, 02:50:08 pm »
I made up a batch of cane arrows.
One of them seems to be (over spined).

Question: Is there any way to (actually) reduce the spine of a cane?

It is already a bit heaver than the rest of the batch so I did not want to add more weight to the point.
However that may be my only choice.

I could always put a heavy blunt type tip on it and use it for small game.

Thanks
David
David Key / N.W. Alabama

Offline ZanderPommo

  • Member
  • Posts: 470
Re: Reducing the spine of a cane
« Reply #1 on: October 06, 2008, 03:15:05 pm »
i know there is a way to do it with heat but I don't know how..................sorry

Zander

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,609
Re: Reducing the spine of a cane
« Reply #2 on: October 06, 2008, 03:53:03 pm »
You can scrape off the rind and scrape or sand them to decrease the spine a little but not much, then you will have to seal it.
   The best way is to make them a bit longer than normal. I cut all my hardwood shoot and cane arrows to 29" for my 26" draw. For each inch over 28" you can subtract 5# of spine weight.   Pat
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Ryano

  • Member
  • Posts: 3,578
  • Ryan O'Sullivan, North Western Pennsylvania
Re: Reducing the spine of a cane
« Reply #3 on: October 06, 2008, 04:12:20 pm »
David, I've gotten away with chucking up one end of the the shaft up in my drill and spinning it through a piece of sand paper in my hand. Not real primitive but it works good for me.  ;)
Its November, I'm gone hunt'in.......
Osage is still better.....

Offline RidgeRunner

  • Member
  • Posts: 1,153
Re: Reducing the spine of a cane
« Reply #4 on: October 07, 2008, 06:31:21 pm »
Thanks for the replies.

I think that stiff arrow is going to become a heavy tipped bunny buster.
It will most likely never be fired at a target more that 15 yards away.

Thanks
David
David Key / N.W. Alabama

Offline Hillbilly

  • Member
  • Posts: 8,248
  • I like tater tots.
Re: Reducing the spine of a cane
« Reply #5 on: October 07, 2008, 09:01:49 pm »
I like to carry one really heavy arrow and one light one at 3D shoots, too-that way you can shoot those close and long shots the same as the normal range ones that you use your matched ones on..
Smoky Mountains, NC

NeolithicHillbilly@gmail.com

Progress might have been all right once but it's gone on for far too long.

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,609
Re: Reducing the spine of a cane
« Reply #6 on: October 08, 2008, 12:04:26 am »
So that's how you do it!  ;)
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 32,116
  • if you have to ask you wouldn't understand ,Tenn.
Re: Reducing the spine of a cane
« Reply #7 on: October 08, 2008, 08:19:20 am »
I had pretty good luck scraping them to reduce the spine,like Pat said then you need to seal them.
The heavy weight don't really matter that much to me at the range I hunt but the heavy/light spine weight dose,They fly wild and I can't hit anything with them. :)
   Pappy
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good

Offline uwe

  • Member
  • Posts: 618
Re: Reducing the spine of a cane
« Reply #8 on: October 08, 2008, 03:00:38 pm »
I only scrap material off to reduce the dia or the thickness. I don`t have any problems withn the spine only the weight is important for me. I heard it from others and made my own experiences that the spine isn`t im portant to the bows. Or do Ihave only some lucky sticks for my bows?
But on the other way I tried them on bows of different drawweight and didn`t have problems.
Regards Uwe