« previous next »
Pages: [1]

Author Topic: Twist  (Read 2396 times)

0 Members and 1 Guest are viewing this topic.

Offline DC

  • Member
  • Posts: 10,396
Twist
« on: September 22, 2015, 12:25:19 pm »
I cut and split this Douglas Maple the other day. The long one has more than 90 degrees of twist and the short one is about 90. If I had run this through the bandsaw instead of splitting it would the bow have held together with that much twist. I'm thinking it's pretty much firewood now.
Logged

Offline wizardgoat

  • Member
  • Posts: 2,397
Re: Twist
« Reply #1 on: September 22, 2015, 12:27:52 pm »
Like vine maple, I'd only ever saw Douglas maple.
Logged

Offline DC

  • Member
  • Posts: 10,396
Re: Twist
« Reply #2 on: September 22, 2015, 12:29:31 pm »
And you wouldn't worry about this much twist compromising the bow. I'm thinking many runouts.
Logged

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Twist
« Reply #3 on: September 22, 2015, 12:33:02 pm »
Run outs are made by the guy laying the stave out, nothing else to blame for them. Me? I wouldn't touch those with a 10 meter pole. And it will worsen as they dry down.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

blackhawk

  • Guest
Re: Twist
« Reply #4 on: September 22, 2015, 12:50:46 pm »
Those will cook some nice weiners and smores!!!  :laugh:
Logged

Offline DC

  • Member
  • Posts: 10,396
Re: Twist
« Reply #5 on: September 22, 2015, 01:14:51 pm »
OK. I'm still wondering, if I had run these logs through the bandsaw and made bows would this much twist cause them to break.
My problem here is I can't see if the log is twisted until I split it, and if it is twisted it's a waste of time and a tree.
Logged

Offline wizardgoat

  • Member
  • Posts: 2,397
Re: Twist
« Reply #6 on: September 22, 2015, 01:47:44 pm »
I haven't made a Douglas bow yet, I have a few staves in th corner though.
On vine maple I've always sawn or used a hatchet to get a flat stavwe, and grain
Run out on smaller Diam stuff hasn't been an issue with me.
Logged

Offline Tree_Ninja

  • Member
  • Posts: 181
  • Clandestine Bow-ops
Re: Twist
« Reply #7 on: September 22, 2015, 07:33:35 pm »
Its a moot point, but no, I doubt a bow would survive if you had used a saw.
 
Were those stems growing nearly horizontal out of a bank?
 
You might get some snow shoes out of that.
Logged

Offline DC

  • Member
  • Posts: 10,396
Re: Twist
« Reply #8 on: September 22, 2015, 08:19:16 pm »
They were growing at about 45 degrees. I may just rough them out following the twist and then take a shot at steaming the twist out. I've done it with yew but it wasn't quite as bad as this. I hate to waste a tree, especially when it's already cut and leaning against my shop wall.
Logged

Offline bowandarrow473

  • Member
  • Posts: 696
Re: Twist
« Reply #9 on: September 22, 2015, 09:54:37 pm »
Try taking the twist out, I feel the same as you, if you cut a tree you have a duty to it to use it as best you can.
Logged
Whatever you are, be a good one.

Offline DC

  • Member
  • Posts: 10,396
Re: Twist
« Reply #10 on: September 22, 2015, 11:44:14 pm »
One half done. Seemed to work OK. Steam sure removes bark. It came off in one piece. I guess I'm going to have to tie it to a 2x4 until it's seasoned.
Logged

Offline osage outlaw

  • Member
  • Posts: 11,952
Re: Twist
« Reply #11 on: September 23, 2015, 12:03:20 am »
You might want to take it a little past straight.  It might have some spring back when you untie it
Logged
I started out with nothin' and I still got most of it left

Offline vinemaplebows

  • Member
  • Posts: 1,419
Re: Twist
« Reply #12 on: September 25, 2015, 01:09:15 pm »
Quote from: wizardgoat on September 22, 2015, 12:27:52 pm
Like vine maple, I'd only ever saw Douglas maple.


Saw Douglas or vine....I agree 100%
Logged
Debating is an intellectual exchange of differing views...with no winners.
Pages: [1]
« previous next »