Author Topic: Couple blades I'm working on.  (Read 2619 times)

0 Members and 1 Guest are viewing this topic.

Stringman

  • Guest
Couple blades I'm working on.
« on: September 26, 2016, 06:57:06 pm »
I was setup at a local event this weekend and had time to work on some blades. I worked the core out of a large Georgetown nodule and then decided to finish it at a later time. I was afraid distraction would cause a mis strike so I set it aside.



The dagger is from a chunk of obsidian and needs a little rework before it's finished.


Offline Outbackbob48

  • Member
  • Posts: 2,752
Re: Couple blades I'm working on.
« Reply #1 on: September 26, 2016, 07:36:54 pm »
Sound wisdom Scott, I have a hard time finishing up points when at events, better to make preforms and continue explaning the process over and over. Nice lookin set of blades. Bob

Offline Trapper Rob

  • Member
  • Posts: 3,718
Re: Couple blades I'm working on.
« Reply #2 on: September 26, 2016, 08:02:43 pm »
Those are some nice blades.

Offline osage outlaw

  • Member
  • Posts: 11,952
Re: Couple blades I'm working on.
« Reply #3 on: September 26, 2016, 08:08:48 pm »
Very nice work Scott!
I started out with nothin' and I still got most of it left

Offline PNewton

  • Member
  • Posts: 400
Re: Couple blades I'm working on.
« Reply #4 on: September 26, 2016, 08:19:20 pm »
Nice looking blades. I never paid too much attention to stone points and knives until I seen your work at Marshall. Now one is on my wish list. Impressive work.

Stringman

  • Guest
Re: Couple blades I'm working on.
« Reply #5 on: September 26, 2016, 08:24:47 pm »
Sound wisdom Scott, I have a hard time finishing up points when at events, better to make preforms and continue explaning the process over and over. Nice lookin set of blades. Bob

Yep, it happens a lot for me. I'll be tripping along and paying about half attention to what I'm doing when SNAP! Not a big deal if the point is small or out of cheap material. But when they are long and purty, it stings a little.

Stringman

  • Guest
Re: Couple blades I'm working on.
« Reply #6 on: September 26, 2016, 08:25:33 pm »
Nice looking blades. I never paid too much attention to stone points and knives until I seen your work at Marshall. Now one is on my wish list. Impressive work.

Well, thank you Paul. Anytime you're ready jus say the word.

Offline bjrogg

  • Member
  • Posts: 10,801
  • Cedar Pond
Re: Couple blades I'm working on.
« Reply #7 on: September 26, 2016, 10:50:11 pm »
Nice Stringman, reminds me of an old Aerosmith song, "my big 10 inch" beautiful as allways.
Bjrogg
A hot cup of coffee and a beautiful sunrise

Offline iowabow

  • member
  • Member
  • Posts: 4,718
Re: Couple blades I'm working on.
« Reply #8 on: September 27, 2016, 06:16:16 am »
Looking good Scott
(:::.) The ABO path is a new frontier to the past!

Offline Aaron H

  • Member
  • Posts: 3,437
Re: Couple blades I'm working on.
« Reply #9 on: September 27, 2016, 07:56:30 am »
Great looking blades Scott

Offline Zuma

  • Member
  • Posts: 4,324
Re: Couple blades I'm working on.
« Reply #10 on: September 27, 2016, 10:40:18 am »
Wow, some big beauties there 8)
Good lines on the dagger.
Zuma
If you are a good detective the past is at your feet. The future belongs to Faith.

Offline Jodocus

  • Member
  • Posts: 897
Re: Couple blades I'm working on.
« Reply #11 on: October 02, 2016, 04:14:58 am »
sweet dagger, very nice, and lovely blades, too!
Don't shoot!

Offline selfbow joe

  • Member
  • Posts: 996
  • 1-812-344-1590
Re: Couple blades I'm working on.
« Reply #12 on: October 02, 2016, 09:02:15 am »
Very nice looking blades.

Stringman

  • Guest
Re: Couple blades I'm working on.
« Reply #13 on: October 02, 2016, 10:56:07 am »
Thanks Jo, I sat down yesterday and adjusted the look on the obsidian dagger. It looks a lot better now. Maybe I can get a new picture posted this afternoon.

Stringman

  • Guest
Re: Couple blades I'm working on.
« Reply #14 on: October 02, 2016, 02:29:38 pm »