Author Topic: cresting jig  (Read 5219 times)

0 Members and 1 Guest are viewing this topic.

Offline Wvfarrier

  • Member
  • Posts: 32
cresting jig
« on: August 17, 2017, 07:33:43 pm »
free cresting my shafts just isnt cutting it.  has anyone made a cresting jig?
Be polite, be courteous but have a plan to kill everyone in the room.

Offline Hawkdancer

  • Member
  • Posts: 5,027
Re: cresting jig
« Reply #1 on: August 17, 2017, 11:00:10 pm »
Funny you should bring that up!  I am about to make one - I envision a base with 2 uprights, slotted to hold the arrow, the base would be about 8-10 inches and the uprights , maybe 4-5 inches.  I think the height would also hold the arrow for wrapping the fletching.  The base would really be determined by how long your crest is.   Not fancy by any means, but a heck of a lot cheaper than $140.00!
Hawkdancer
Life is far too serious to be taken that way!
Jerry

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,461
Re: cresting jig
« Reply #2 on: August 17, 2017, 11:17:59 pm »
Hawkdancer, would you post a build along with pics. I'm sure lots of folks would love to see it.
 
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Aaron H

  • Member
  • Posts: 3,437
Re: cresting jig
« Reply #3 on: August 18, 2017, 07:29:57 am »
I would be interested in seeing that as well Hawkdancer

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: cresting jig
« Reply #4 on: August 18, 2017, 08:16:22 am »
I have one. I took an old cordless drill and screwed it flat on a 1 x 6 x 30 board. The chuck has a piece of rubber hose over it that gently grabs the shaft. The other end of the board just has a simple "V" cradle cut from the same board. Works fine and cost me zero dollars.
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline Aaron H

  • Member
  • Posts: 3,437
Re: cresting jig
« Reply #5 on: August 18, 2017, 09:35:56 am »
Pictures or it didn't happen...You should know that by now Chris  ;)

Offline DC

  • Member
  • Posts: 10,396
Re: cresting jig
« Reply #6 on: August 18, 2017, 02:49:29 pm »
What brand of drill did you use? I made one like that and it won't go slow enough for me to serve the fletching nicely. I used a battery charger for a power supply and had to wire a dimmer switch into it to slow it down. I don't think the dimmer is doing my charger a lot of favors.

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: cresting jig
« Reply #7 on: August 18, 2017, 03:02:14 pm »
Pictures or it didn't happen...You should know that by now Chris  ;)

 ;D  Nice one Aaaron
I started out with nothin' and I still got most of it left

Offline lebhuntfish

  • Member
  • Posts: 3,800
  • If the wood will bend, I'll make it beautiful!
Re: cresting jig
« Reply #8 on: August 18, 2017, 03:35:22 pm »
Pictures or it didn't happen...You should know that by now Chris  ;)

Yeah!  >:D

Patrick
Once an Eagle Scout, always an Eagle Scout!

Missouri, where all the best wood is! Well maybe not the straightest!

Building a bow has been the most rewarding, peaceful, and frustrating things I have ever made with my own two hands!

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: cresting jig
« Reply #9 on: August 18, 2017, 05:13:32 pm »
What? Cant hear ya'? What?

Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: cresting jig
« Reply #10 on: August 18, 2017, 05:17:11 pm »
Take the bolts/screws out of the body of the drill and lay it flat on the board, shim where needed. Then just replace the screws/bolts with drywall screws long enough to go through and into the board. You will have to find a way to keep the trigger pulled, I use spring clamps. I have two different tube diameters "necked" down to fit 11/32 tight'ish.

And that's where the term "Gerry riggin" came from :)
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline lebhuntfish

  • Member
  • Posts: 3,800
  • If the wood will bend, I'll make it beautiful!
Re: cresting jig
« Reply #11 on: August 18, 2017, 06:23:34 pm »
Ok Chris,  I can believe that!
Simple but effective,  thats the way I like it. 
Do you use a reastat to slow it down?

Patrick
Once an Eagle Scout, always an Eagle Scout!

Missouri, where all the best wood is! Well maybe not the straightest!

Building a bow has been the most rewarding, peaceful, and frustrating things I have ever made with my own two hands!

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: cresting jig
« Reply #12 on: August 18, 2017, 07:10:01 pm »
Nope. Its an old GM assy line drill. Its very slow already.
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline DC

  • Member
  • Posts: 10,396
Re: cresting jig
« Reply #13 on: August 18, 2017, 08:48:23 pm »
The new ones seem to be too fast. I think one of those old electric screwdrivers would do the trick but I haven't found one. I've thrown 2 or 3 of them out over the years but when I want one. nahhhh ;D ;D

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,461
Re: cresting jig
« Reply #14 on: August 18, 2017, 11:28:15 pm »
A sewing machine motor with a foot control rheostat works well. I used the motor from a rock tumbler.
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC