Author Topic: Share your tips and tricks.  (Read 24606 times)

0 Members and 2 Guests are viewing this topic.

Offline bjrogg

  • Member
  • Posts: 6,952
  • Cedar Pond
Re: Share your tips and tricks.
« Reply #75 on: November 30, 2018, 09:25:35 am »
Pay attention and figure out which way the grain is running off on your first couple strokes with the draw knife. A lot of time I will stroke down the limb to remove wood on one side, and stroke up the limb on the other to prevent the knife from digging to deep.

If the grain is being especially difficult to work with a draw knife, use a sureform rasp and make long even strokes at a 45* angle to the limb instead.

I've lost a few bows to grain tearing, hopefully these will help new bowyers.


Yup and some wood you just have to use a rasp. Elm is one that comes to mind. Also knots are best reduced with rasp.
A hot cup of coffee and a beautiful sunrise

Offline burtonridr

  • Member
  • Posts: 212
Re: Share your tips and tricks.
« Reply #76 on: December 06, 2018, 08:19:01 pm »
If you have a press on field point, glued with the melt stuff, and the shaft break right at the field point so you cant grab the shaft with pliers or your fingers. Use a wood screw, screw it in to the busted piece of shaft, heat the field point to melt the glue, then pull the old shaft piece out using the wood screw to grab on.

Learned that one tonight  :OK

Hopefully the description is clear enough.
Offgrid mtn living

Offline jimmi the sammi

  • Member
  • Posts: 51
Re: Share your tips and tricks.
« Reply #77 on: February 04, 2019, 03:20:01 pm »
2 quick ones.  Use a 5/16" tap inside your field points.  Put the field point in a vise and screw the tap into the point back and forth a little at a time until it bottoms out.  Glue the point on with your favorite glue.  No more pulled off field points in targets.

Several have mentioned ways to cover your bow making tools.  Go to your local fire station and ask for discarded fire hose.  It comes in many sizes and works perfectly for covering files, rasps, and all your other cutting tools.  I made a carrying board out of 1/4" plywood with fire hose stapled to it to hold each of my tools separately and make it much easier to carry from place to place with a handle cut out at the top of the board.

Offline Eric Krewson

  • Member
  • Posts: 3,577
Re: Share your tips and tricks.
« Reply #78 on: February 05, 2019, 06:23:48 am »
Well, I tried the tap solution years ago, it was better than a non tapped point but didn't work all that well overall. A better solution is to wrap a piece of sandpaper around an old shaft with a point taper, insert in the point and spin the shaft around a few times, this will clean the inside of the point to bare metal. Tap out the dust and glue the point on with two ton epoxy, it isn't coming off and can still be removed with heat but will need a bit more than one would use with hot melt.

Offline txdm

  • Member
  • Posts: 137
Re: Share your tips and tricks.
« Reply #79 on: February 15, 2019, 11:45:53 am »
On board bows, it's tempting to do some pre-shaping on the block of wood that you plan to glue on to make the handle thicker. But just leaving that block square gives you better surfaces to clamp down on for glueup, especially on the ends where the fades will meet the bow limbs.

Offline Woodely

  • Member
  • Posts: 349
Re: Share your tips and tricks.
« Reply #80 on: February 26, 2019, 08:47:15 pm »
Here is an easy way to mount a belt sander upside down on a saw horse.
"Doing bad work is an exercise in futility, but honestly making mistakes is trying your best."

Offline txdm

  • Member
  • Posts: 137
Re: Share your tips and tricks.
« Reply #81 on: March 08, 2019, 11:03:28 am »
A crescent wrench can help mark string grooves precisely on both sides of the limb.

Offline ksnow

  • Member
  • Posts: 498
Re: Share your tips and tricks.
« Reply #82 on: March 08, 2019, 11:52:44 am »
I'm stealing that one, txdm. Simply brilliant.

Kyle

Offline DC

  • Member
  • Posts: 8,297
Re: Share your tips and tricks.
« Reply #83 on: March 08, 2019, 03:55:34 pm »
That is clever, good one!
Vancouver Island
If you don't have any questions you must not be paying attention.

Offline zoomer

  • Member
  • Posts: 22
Re: Share your tips and tricks.
« Reply #84 on: October 06, 2019, 08:42:27 am »
I had trouble outlining (width) on a gnarly, crowned staves. Here's what I discovered today:
1) draw a straight line by joining many short lines one-by-one, aligning the ruler with already drawn lines. The line will follow the grain this way;
2) from drawn line, measure desired width and mark it with a dot. Do this every half an inch or so;
3) connect the dots.
Now you have an outlined width that follows the grain precisely and is constant along its length. Perhaps everyone already know this.