Author Topic: Sawmill blade knife  (Read 4556 times)

0 Members and 1 Guest are viewing this topic.

Offline bubby

  • Member
  • Posts: 11,054
Sawmill blade knife
« on: April 07, 2018, 08:49:44 pm »
A friend of mine is a millwright at a mill locally. When I had my last replacement surgery he cut a bunch of blanks out with the plasma cutter and brought them to my in-laws. I think they were from trimsaw blades , all I know is they get real hard.anyway I cleaned one up and ground the bevels in , then got it heat treated. It's in the toaster oven now
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline FilipT

  • Member
  • Posts: 821
Re: Sawmill blade knife
« Reply #1 on: April 08, 2018, 03:52:57 am »
Are you going for a "small bowie" look here?

Offline Hawkdancer

  • Member
  • Posts: 5,027
Re: Sawmill blade knife
« Reply #2 on: April 08, 2018, 12:44:06 pm »
Good looking start.  Looks like your "forge" can double for grilling steaks at a somewhat cooler temperature! (=) (f) (f)! Lol!
Life is far too serious to be taken that way!
Jerry

Offline bubby

  • Member
  • Posts: 11,054
Re: Sawmill blade knife
« Reply #3 on: April 08, 2018, 01:53:50 pm »
Hawk man I have used that for a forge before , just not for this
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline bubby

  • Member
  • Posts: 11,054
Re: Sawmill blade knife
« Reply #4 on: April 08, 2018, 09:13:09 pm »
Well I cleaned up the blade , then drilled the pin hole and did the ferric etchant dip. I anneled the tangto drill it and still couldn't get a hole in it so I used a carbide ball Burr to do it
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Hawkdancer

  • Member
  • Posts: 5,027
Re: Sawmill blade knife
« Reply #5 on: April 08, 2018, 11:27:47 pm »
Doesn't sound like beginner steel!  Maybe a concealed tang sealed with expory!
Hawkdancer
Life is far too serious to be taken that way!
Jerry

Offline bubby

  • Member
  • Posts: 11,054
Re: Sawmill blade knife
« Reply #6 on: April 08, 2018, 11:47:59 pm »
Oh it's a hidden tang , but by good I will pin it !! Lol
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Hawkdancer

  • Member
  • Posts: 5,027
Re: Sawmill blade knife
« Reply #7 on: April 09, 2018, 11:22:15 am »
Not sure if it is correct info, but some one told me those titanium bits go through any thing, but thet ain't cheap.  Is that real tough steel?  Or was the annealing not quite right, or both?
Hawkdancer
Life is far too serious to be taken that way!
Jerry

Offline bubby

  • Member
  • Posts: 11,054
Re: Sawmill blade knife
« Reply #8 on: April 09, 2018, 12:42:23 pm »
I have had blades that titanium bit struggle with, but carbide, carbide will take a bite out of most anything. It was annealed properly but I didn't happen to have a titanium bit handy anyways
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹