Author Topic: Heat resistant finish?  (Read 1555 times)

0 Members and 1 Guest are viewing this topic.

Offline Hawkdancer

  • Member
  • Posts: 5,027
Heat resistant finish?
« on: November 28, 2018, 11:55:38 am »
Has any one tested finishes for heat resistance?  Truoil, polyurethane, spar varnish, wood bowl finish, home made finishes?  I'm making some trivets and want to seal them.  I know most anything will scorch if it gets too hot, but normal cooking temps should not, I think! -C- >:D (lol)!  I am testing spray poly, salad bowl, and my beeswax/flaxseed oil spoon finish.  Thanks,
Hawkdancer
Life is far too serious to be taken that way!
Jerry

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: Heat resistant finish?
« Reply #1 on: November 28, 2018, 02:54:55 pm »
For cooking equipment could it be to use the same thing used on wood stoves?I use stove black on my stoves.It's baked on.The stove does'nt rust any.
Our cast iron pans are seasoned with vegetable oil on the inside.
« Last Edit: November 28, 2018, 03:01:54 pm by BowEd »
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline Hawkdancer

  • Member
  • Posts: 5,027
Re: Heat resistant finish?
« Reply #2 on: November 29, 2018, 12:26:12 am »
The trivet is used to set hot dishes on, usually on on the table, but also near the stove.  Stove black would probably darken the wood or act like paint, and blacken it completely.  I have seen some trivets that were badly scorched from having a too hot skillet set on them directly from the stove or oven.  I am going try try spar urethane as well.  I think my test pieces will be cured enough to test tomorrow by placing a cooking temperature skillet on the and see what happens.
Hawkdancer
Life is far too serious to be taken that way!
Jerry

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: Heat resistant finish?
« Reply #3 on: November 29, 2018, 05:26:15 am »
Excuse me.I thought your trivet was made of iron for a camp fire.Got any pictures of your project?
« Last Edit: November 29, 2018, 05:42:08 am by BowEd »
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline Hawkdancer

  • Member
  • Posts: 5,027
Re: Heat resistant finish?
« Reply #4 on: November 29, 2018, 11:08:36 am »
I did forget to mention they were wood!  Opps! Will try to get some pictures this afternoon.  Most of the pieces are walnut, and I will make cork feet for them.  I will sand them down to320 grit with my random orbital sander before I finish them.
Hawkdancer
Life is far too serious to be taken that way!
Jerry

Offline Hawkdancer

  • Member
  • Posts: 5,027
Re: Heat resistant finish?
« Reply #5 on: November 30, 2018, 09:58:00 am »
Here are some pics, I hope!
All the wood is walnut, sanded to 320 grit.  First pic is my test pieces, l>r, plain unsanded, spray poly, GF salad bowl finish, and my 4:1 flaxseed oil/beeswax, after having a semi hot skillet set on them, simultaneously.  Spoon finish needs a couple more coats, and longer cure time, polyurethane held up well.
https://i.imgur.com/93j2p3J_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
Next pic should show a parquet coaster and a trivet.
Life is far too serious to be taken that way!
Jerry

Offline Hawkdancer

  • Member
  • Posts: 5,027
Re: Heat resistant finish?
« Reply #6 on: November 30, 2018, 10:01:43 am »
Looks like it posted my whole camera roll but just tap on the walnut cylinders!
Hawkdancer
Life is far too serious to be taken that way!
Jerry