Author Topic: Making a gas forge  (Read 21389 times)

0 Members and 1 Guest are viewing this topic.

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: Making a gas forge
« Reply #30 on: January 08, 2019, 05:28:01 pm »
Pretty blame neat Clint!!Now how hot is it going to get in there?2000 degrees or better?
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: Making a gas forge
« Reply #31 on: January 08, 2019, 08:20:10 pm »
I'm not sure Ed.  I'm hoping it gets hot enough for forge welding.
I started out with nothin' and I still got most of it left

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 31,712
  • if you have to ask you wouldn't understand ,Tenn.
Re: Making a gas forge
« Reply #32 on: January 09, 2019, 05:59:11 am »
That is looking very good Clint. :)
 Pappy
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: Making a gas forge
« Reply #33 on: January 11, 2019, 04:58:53 pm »
The rigidizer took longer than expected to dry because the temperature dropped.  I put a space heater blowing through it for 24 hours and that dried it out.  I put the first coat of Kast-O-lite over the insulation.  It's a castable refractory cement.  I bought 15 lbs of this stuff and used about 6 lbs so far on the base coat. 




I started out with nothin' and I still got most of it left

Offline TRiggs

  • Member
  • Posts: 59
Re: Making a gas forge
« Reply #34 on: January 12, 2019, 09:30:59 am »
Just a little tip, you should remove the feet on your forge and re-weld them so that your torches are straight up and down. Your torches come in at a 1:30 position and blow to a 7:30 position that means your heat goes that way also your going to want your heat right in the center where your metal is gong to be sitting you will save gas and heat your metal faster.
American Blade Smith Apprentice

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: Making a gas forge
« Reply #35 on: January 12, 2019, 10:02:21 am »
Just a little tip, you should remove the feet on your forge and re-weld them so that your torches are straight up and down. Your torches come in at a 1:30 position and blow to a 7:30 position that means your heat goes that way also your going to want your heat right in the center where your metal is gong to be sitting you will save gas and heat your metal faster.

I was told to have them come in at an angle like that to get the heat swirling around the chamber.
I started out with nothin' and I still got most of it left

Offline KHalverson

  • Member
  • Posts: 755
Re: Making a gas forge
« Reply #36 on: January 12, 2019, 01:11:16 pm »
looks good with the refractory cement.
it should keep the inswool stabilized very well.
if your gonna forge weld ya might wanna put a hard fire brick in the bottom as a sacrificial floor.
flux will break down some refractory materials.

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: Making a gas forge
« Reply #37 on: January 12, 2019, 01:28:43 pm »
I will have extra refractory left over.  I was going to build some forms and make a few bricks from it to use as a replaceable floor.  I'm going to do a second coat of refractory and then the IR reflective coating.   
I started out with nothin' and I still got most of it left

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: Making a gas forge
« Reply #38 on: January 16, 2019, 04:44:30 pm »
I did a second layer of the refractory cement today.  I added extra to the bottom to make a flat surface.  I will need to let it dry out for a good while before moving on to the final step.  It's almost finished.  I have 4 lbs of refractory left.  I should be able to make several bricks for the bottom.

I started out with nothin' and I still got most of it left

Offline KHalverson

  • Member
  • Posts: 755
Re: Making a gas forge
« Reply #39 on: January 16, 2019, 04:54:02 pm »
that looks really good!
im watching this with anticipation cause I need to build a new forge.

Online bjrogg

  • Member
  • Posts: 10,713
  • Cedar Pond
Re: Making a gas forge
« Reply #40 on: January 18, 2019, 09:28:22 am »
that looks really good!
im watching this with anticipation cause I need to build a new forge.


me to
bjrogg
A hot cup of coffee and a beautiful sunrise

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: Making a gas forge
« Reply #41 on: January 24, 2019, 06:54:52 pm »
I ran out of propane trying to go through the curing steps the other day.  I got a new tank and started again today.  This thing will put out some serious heat.  I need to do another heat tomorrow and then it's ready for the IR coating.  That is the last step. 






After shutting it off the inside glows




I took some of the left over refractory and made a brick to put in the bottom of the forge. 



I started out with nothin' and I still got most of it left

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: Making a gas forge
« Reply #42 on: January 24, 2019, 06:57:43 pm »
Here is a short video of it running.

ht  tps://youtu.be/cfu5TIl4dHU
I started out with nothin' and I still got most of it left

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,461
Re: Making a gas forge
« Reply #43 on: January 24, 2019, 08:25:54 pm »
Clint, you better bolt that thing to the workbench. Looks like it will heat something up in no time...and heat your shop.
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline osage outlaw

  • Member
  • Posts: 11,951
Re: Making a gas forge
« Reply #44 on: January 24, 2019, 08:45:09 pm »
I need to tune it down a little Pat.  I had the regulator wide open.
I started out with nothin' and I still got most of it left