Author Topic: .45 Lancaster  (Read 19170 times)

0 Members and 1 Guest are viewing this topic.

Offline sleek

  • Member
  • Posts: 6,680
Re: .45 Lancaster
« Reply #15 on: July 18, 2020, 01:19:09 pm »
I want one of these soooo much. I just don't have the time to invest in learning a new skill. I guess I have to just watch you masters of the trade for now.
Tread softly and carry a bent stick.

Dont seek your happiness through the approval of others

Offline Parnell

  • Member
  • Posts: 5,551
Re: .45 Lancaster
« Reply #16 on: July 18, 2020, 02:07:40 pm »
Master!  Haha!  I’m a newbie, Sleek.  But, thanks.  I hope you can get it in time.
1’—>1’

Offline Mike Yancey

  • Member
  • Posts: 222
Re: .45 Lancaster
« Reply #17 on: July 18, 2020, 05:46:57 pm »
Good job on the lock bolt!

Offline Parnell

  • Member
  • Posts: 5,551
Re: .45 Lancaster
« Reply #18 on: July 19, 2020, 11:54:25 am »
Thanks, Mike.
1’—>1’

Offline Parnell

  • Member
  • Posts: 5,551
Re: .45 Lancaster
« Reply #19 on: February 12, 2021, 10:00:58 am »
I’ve made more progress after having done some house renovations.  Butt plate looks good...one small spot I’ll shim.  Heel plate is in and I’m happy.  I have a little more inletting to do on the lock plate, I think.  Currently it is sitting a little proud over the stock.  Thinking to bring it near flush.

Opinions?

I should drill the ramrod thimbles and tailpipe this weekend.
Making progress again.
1’—>1’

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,462
Re: .45 Lancaster
« Reply #20 on: February 12, 2021, 10:48:59 am »
Looking good, Steve. I've never built one but it still looks good.   ;D
Hope you and Angie are doing well.  :OK
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Parnell

  • Member
  • Posts: 5,551
Re: .45 Lancaster
« Reply #21 on: February 12, 2021, 10:58:31 am »
Hi Pat!  Yeah, we are hanging in there and keeping well.  Glad to see your ALB thread going.  I hope the same for you all, also.

JW-If you see this, yeah, still at it! Saw your post on the other thread.  You been working on any projects?
1’—>1’

Offline JW_Halverson

  • Member
  • Posts: 11,823
Re: .45 Lancaster
« Reply #22 on: February 12, 2021, 01:23:10 pm »
Hi Pat!  Yeah, we are hanging in there and keeping well.  Glad to see your ALB thread going.  I hope the same for you all, also.

JW-If you see this, yeah, still at it! Saw your post on the other thread.  You been working on any projects?

On and off playing with making powderhorns and shooting bags. Nothing major.
Guns have triggers. Bicycles have wheels. Trees and bows have wooden limbs.

Offline Eric Krewson

  • Member
  • Posts: 5,306
Re: .45 Lancaster
« Reply #23 on: February 13, 2021, 08:21:25 pm »
I finally got the toe plate on my Haines rifle, something slipped and I got some major inletting gaps, I shimmed the biggest one, tried to shim a smaller one and the toe plate wouldn't fit in the inlet.

I hate gaps so I tried a new gap filler, my old dent removing steam iron. I put a piece of wet tee shirt over the toe plate and gave the wood and plate good steaming, now it looks like the toe plate grew into the wood, no gaps.

Offline chamookman

  • Member
  • Posts: 2,971
Re: .45 Lancaster
« Reply #24 on: February 14, 2021, 04:13:29 am »
Sounds like a good save Eric  :-M ! Bob
"May the Gods give Us the strength to draw the string to the cheek, the arrow to the barb and loose the flying shaft, so long as life may last." Saxon Pope - 1923.

Offline Parnell

  • Member
  • Posts: 5,551
Re: .45 Lancaster
« Reply #25 on: February 15, 2021, 05:29:03 pm »
Wow, very interesting, Eric.  I’ll try it.
1’—>1’

Offline Parnell

  • Member
  • Posts: 5,551
Re: .45 Lancaster
« Reply #26 on: April 03, 2021, 10:39:06 am »
Eric, used your trick with the butt cap and it helped a bit.

On tothe nose cap.  First time doing this, so any tips appreciated.
1’—>1’

Offline Parnell

  • Member
  • Posts: 5,551
Re: .45 Lancaster
« Reply #27 on: April 03, 2021, 10:50:55 am »
So, sitting flush and parallel to the stock, is the plan.
1’—>1’

Offline Eric Krewson

  • Member
  • Posts: 5,306
Re: .45 Lancaster
« Reply #28 on: April 04, 2021, 07:55:23 pm »
You are supposed to have 1/8" of the barrel sticking out past the nose cap. If you trim the wood back just enough to put the nose cap on the barrel backwards you can draw on the stock around the outside of the brass to give you a starting point for wood removal.

I lost this nose cap on my workbench and forgot to neutralize the browning solution, it got a little too brown.


Offline Parnell

  • Member
  • Posts: 5,551
Re: .45 Lancaster
« Reply #29 on: August 26, 2021, 08:49:22 pm »
Here are some pictures of where I am in the project.  Slower with the heat but still moving along.

Question…I am having trouble adjusting the double set trigger to work properly.  When I cock the lock it alternates with releases…one the set trigger releases the lock…cock again then the hair trigger releases the lock.  When I remove the trigger completely it seems to work properly.  That is, it catches with the set and releases on the hair…but that is not under the tension of the lock.

How to go about adjusting?
1’—>1’