Author Topic: Carving/scrimshaw and Cow Horns  (Read 7696 times)

0 Members and 2 Guests are viewing this topic.

Offline SKÖLDMÖ

  • Member
  • Posts: 3
Carving/scrimshaw and Cow Horns
« on: December 16, 2016, 10:36:14 am »
I am making a drinking horn using cow horn. I would like to add some carvings into it, and would drink the best method to carve bone. I do not want to use any form of power drill. Thanks guys!
Sköldmö (Katie Eklund)

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,609
Re: Carving/scrimshaw and Cow Horns
« Reply #1 on: December 16, 2016, 12:57:11 pm »
An awl with a sharp point should work fine for it. All you are doing is scratching the surface, wiping on the ink and wiping off the excess leaving the ink in the scratched. For carving a rat tail rasp, files and maybe a sharp blade.
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline stuckinthemud

  • Member
  • Posts: 2,348
    • avenue woodcarving
Re: Carving/scrimshaw and Cow Horns
« Reply #2 on: December 16, 2016, 04:23:05 pm »
For actual carving then a few palm chisels from a good manufacturer are a must.  The essential is a v-tool and a nearly flat gouge (a number 3 on the English system); a deep u-gouge is also a really good idea (number  8 )- usually you can only buy palm gouges in sets and these 3 tools are pretty much in all of them but its always worth checking.
« Last Edit: December 18, 2016, 10:45:57 am by stuckinthemud »

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,909
  • Eddie Parker
Re: Carving/scrimshaw and Cow Horns
« Reply #3 on: December 16, 2016, 09:00:06 pm »
I have some tools I made up for scrimshawing. One is a nail sanded on a belt sander till it is needle sharp and another is a large leather sewing needle, both mounted in a small wooden handle. I also use an Exacto knife. I sketch what I want on the horn with a pencil and then cut and scrape with the tools. Then rub in real good into the scratches, India ink, or go over the lines with a Sharpie.The sharpie is what I use most and don't have to sand as much to get rid of the excess out of the scratches. And, it lasts for a long time and doesn't fade after it's sealed.
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline EdwardS

  • Member
  • Posts: 229
Re: Carving/scrimshaw and Cow Horns
« Reply #4 on: December 17, 2016, 02:27:06 pm »
I carve horn with files and sandpaper for the most part.  If I'm carving knotwork or some similar I use a Dremel tool.  Be sure to wear a mask if you do so though.

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,909
  • Eddie Parker
Re: Carving/scrimshaw and Cow Horns
« Reply #5 on: December 17, 2016, 06:26:41 pm »
I'll get some pictures of my tools up tomorrow.
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,909
  • Eddie Parker
Re: Carving/scrimshaw and Cow Horns
« Reply #6 on: December 18, 2016, 08:24:29 pm »
Here is what I use.
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,609
Re: Carving/scrimshaw and Cow Horns
« Reply #7 on: December 18, 2016, 08:34:50 pm »
Nice scrimshaw Eddie.   8)
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,909
  • Eddie Parker
Re: Carving/scrimshaw and Cow Horns
« Reply #8 on: December 18, 2016, 09:24:35 pm »
Thanks, Pat.
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline Redhand

  • Member
  • Posts: 704
  • Marlen Murdock PM109458
Re: Carving/scrimshaw and Cow Horns
« Reply #9 on: December 18, 2016, 11:26:46 pm »
For scrimshaw I use a awl. I file the awl to a needle point, it makes it easy to scratch the piece of bone that I'm working on at the time. Before I start doing scrimshaw work I get the piece sanded down to the finish I want, then I draw the design with a pencil, then I spray shellac over the piece, after the shellac has dried, then I use the awl to scratch in the design, then I put the India ink on, once I get the design to my liking. I use acetone to wipe off the shellac. This method seems to work good for me.

I've made necklaces out of antler that I done scrimshaw work on.
Northern Ute

Offline Hawkdancer

  • Member
  • Posts: 5,039
Re: Carving/scrimshaw and Cow Horns
« Reply #10 on: January 05, 2017, 06:08:04 pm »
Katie,
Most woodworking shops, such as Woodcraft, carry the individual palm knives and gouges.  You also need a carver's glove, or a palm pad.
Have fun!
Hawkdancer(Jerry Mc Connell)
Life is far too serious to be taken that way!
Jerry

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: Carving/scrimshaw and Cow Horns
« Reply #11 on: January 05, 2017, 06:24:45 pm »
Nice work mullet.
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline chamookman

  • Member
  • Posts: 3,018
Re: Carving/scrimshaw and Cow Horns
« Reply #12 on: January 06, 2017, 04:05:36 am »
Way cool Eddie ! Bob
"May the Gods give Us the strength to draw the string to the cheek, the arrow to the barb and loose the flying shaft, so long as life may last." Saxon Pope - 1923.

Offline mullet

  • Global Moderator
  • Member
  • Posts: 22,909
  • Eddie Parker
Re: Carving/scrimshaw and Cow Horns
« Reply #13 on: January 06, 2017, 11:19:33 am »
Thank you.
Lakeland, Florida
 If you have to pull the trigger, is it really archery?

Offline YosemiteBen

  • Member
  • Posts: 1,952
Re: Carving/scrimshaw and Cow Horns
« Reply #14 on: January 09, 2017, 10:04:32 pm »
Many thanks for the thoughts and tips... one more "hobby" I would like to get into...